- Aggregates Manager - http://www.aggman.com -
Critical Watch Spots for Conveyors
Posted By admin On September 1, 2013 @ 6:00 am In Articles,Equipment,Equipment Management,News | No Comments
by Ryan Grevenstuk and Patrick Mukushina
It’s easy not to see a common problem when looking at your belt conveyor system every day, but a quick visual inspection can mean the difference between a productive day and a costly day for your aggregate operation. It’s also helpful to know what to look for when you’re walking the line because small irregularities can rob an operation of productivity.
Listed here are the top 10 conveyor crimes that you can identify with a simple visual inspection, what problems they can cause, and how to fix them in a short period of time.
1.Crime: Damage to belt cleaners, premature wear of fasteners, carryback, mistracking of the belt.
Culprit: Unskived splices, fasteners interfering with the cleaners.
Solution: Skive your belt before applying splices, when possible, and use low-profile fasteners with a coined edge. Make sure all manufacturer’s instructions are followed when splicing, including proper squaring of the belt.
2.Crime: Premature belt splice failure, uneven lagging wear, early cover wear at trough line.
Culprit: Poor transition distance.
Solution: Check your transition distances. Verify that your transition distances are in line with CEMA standards. Typically for fabric belts, CEMA recommends a transition distance of four times the belt width.
3.Crime: Belt ripping right behind the splice, premature belt failure.
Culprit: Fasteners that are too large for the smallest pulley.
Solution: Check the minimum pulley diameters (where the belt wraps 90 degrees or more) against both the belt manufacturer’s recommendations, as well as the fastener manufacturer’s recommendations. Using a pulley diameter that is smaller than the belt and/or fastener’s recommended size can produce excessive bending stresses with the possibility of belt splice failure.
4.Crime: Belt slippage.
Culprit: Small pulleys.
Solution: The proper pulley diameter is crucial to belt performance. When it comes to slippage, the surface area where the belt goes from full tension (top) to partial tension (bottom) and “shrinks” puts an extensive amount of pressure on the lagging to move with it and prevent slip. While CEMA does not specifically recommend a pulley diameter by application, the engineers of conveyor systems make recommendations for pulley diameters based on the design of the conveyor. Often, the small pulley will be substituted to save costs without consideration for this belt shrink — if they minimize the pulley size, they also minimize the area in which the lagging can help the belt shrink as it wraps around the pulley. Reducing the size of the pulley too much may cause slippage.
5.Crime: Mistracking, poor splice life.
Culprit Improperly squared belt.
Solution: Square belt using appropriate tools. Squaring the belt involves marking the center of the belt at 3- to 5-foot intervals for approximately 20 feet from the splice area, drawing a center line based on those markings, and using a square to draw a line that is perpendicular to the average center line across the belt width. Don’t forget to use a proper belt cutter (as opposed to a utility knife) for a safer, straighter cut.
6.Crime: Spillage at the load zone.
Culprit: Poor skirting, no impact protection.
Solution: Check and maintain skirting with an easy-to-use system. Skirting is important in the load zone because it stops material spillage leaks, controls dust emissions, and eliminates other resulting problems, such as belt damage and mistracking. Seek out a skirting system that is easy to service and has corrosion-resistant components for less maintenance. You will also want to ensure that the proper impact protection is available and the belt is properly supported in the load area. Your impact protection should take into account lump weight and drop height, as well as deliver maximum protection to your belt in the load zone.
7.Crime: Belt damage, conveyor structure damage.
Culprit: Belt mistracking.
Solution: Identify the cause of the mistracking and install a belt trainer. Misalignment of rollers or pulleys, an incorrect splice, and material buildup are just a few of the things that can get your belt off track. Friction and tension have been proven to provide effective tracking when used together. Choose a tracker with a pivot and tilt design that provides friction and changes the tension profile of the belt.
8.Crime: Belt damage from seized rollers.
Culprit: Seized rollers cut into belt.
Solution: Regularly inspect conveyor for seized (non-rotating) rollers. For steel rollers, look for flat spots with sharp edges; these should be replaced immediately or risk cutting the belt. For composite rollers with a steel core, look for flat spots with sharp edges; these should be replaced immediately or risk cutting the belt. For composite rollers without a steel core, replace when feasible.
9.Crime: Belt cleaners not working properly.
Culprit: Incorrectly mounted cleaners or belt cupped when passing by cleaners.
Solution: Ensure that the cleaners are mounted correctly by reviewing installation instructions. If the belt is cupped, introduce a hold-down roller to flatten the belt and ensure proper cleaner to belt contact.
1.Crime: Poor cleaning edge and a dirty belt.
Culprit: Poor attack angle, worn blade, or incorrect blade in reference to the material path.
Solution: Pole location is vital to the success of the cleaner because it permits the correct blade attack angle, encourages maximum cleaning performance, and ensures maximum blade life because the entire wear area of the blade can be used. Optimal cleaning can be attained by paying close attention to the material path of the belt, which is typically the center two-thirds of the belt width. Choosing a blade that is only slightly wider than the material path can decrease blade wear and replacement.
Along with visual checks every day, operations should perform a yearly belt conveyor audit. The audit can be done by an internal team, but participation by a third party may be helpful. Simple maintenance tasks that may have gone unnoticed can be identified and addressed by your team, or components can be replaced that will make your equipment run more efficiently. If nothing else, an audit can help keep your equipment running longer.
Over time, carryback, spillage, improper fastener selection, and mistracking can cause serious problems for your belt conveyor system. Although these may seem to be everyday issues, solutions are available and are integral to your operation’s success. All too often, plant operators don’t even realize there’s a problem until the crime has been committed and production is halted. In the end, it all affects the operation’s bottom line. Don’t let these culprits harm your operation.
Ryan Grevenstuk is a senior product manager, Downers Grove, Ill.-based Flexco. Patrick Mukushina is a product manager with the company.
Article printed from Aggregates Manager: http://www.aggman.com
URL to article: http://www.aggman.com/critical-watch-spots-for-conveyors/
URLs in this post:
 Image: http://www.aggman.com/files/2013/08/CSIUntitled-11.gif
 Image: http://www.aggman.com/files/2013/08/cleanersUntitled-1.gif
 Image: http://www.aggman.com/files/2013/08/pulleyUntitled-1.gif
Copyright © 2009 Aggregates Manager. All rights reserved.