May 2008 – RollOuts
Your complete guide to new and updated equipment and supplies in the aggregates industry.
by Kirk Landers, Editorial Director
Rethinking the 16-yard loader
Caterpillars’s new K-series 992 wheel loader gets a new 801-horsepower Tier 2 engine and a host of design upgrades to make it a more cost-efficient mining loader. The new engine is the same one used to power the recently introduced 993K loader, the 777F truck, and the D11T dozer. Designed to load the 70-ton Cat 775 truck in three passes or the 100-ton 777 in four or five passes, the 992K actually carries a lower breakout force and smaller payload rating than the 992G it replaces. Cat engineers say the payload reduction improves the life expectancy of the machine, and the reduction in break out force doesn’t affect cycle times in typical mining applications. For applications demanding greater breakout force and higher payloads, Cat recommends the 993K.
Among the major improvements to the 992K is Cat’s new load-sensing Positive Flow Control hydraulics. The system employs extra sensors at the hydraulic pumps to provide faster responsiveness that Cat says the operator can feel and use. The 992K also gets a new boom that includes fabricated linkage components and factory-sealed sleeve bearing pins that don’t require daily service. Also new is a modular radiator with copper fins; the efficiency of the copper fins reduces the size of the cooling package, allowing enhanced sight lines to the rear, according to Cat.
Hybrid mobile crusher
Eagle Crusher has rolled out a hybrid-powered, track-mounted impactor plant. The Hybrid Traxx features diesel electrical power for both the impactor and the plant; the tracks are driven by an open loop, single-pump hydraulic system. The plant features the new UltraMaxII 4144 impactor, which has hydraulically adjustable curtains for precise product control and reduced wear costs. The main power plant is a 325-horsepower diesel.
Adjustable triple screen
Terex Powerscreen has added the H5163 to its offerings of horizontal screens. It has been fitted with a Terex Cedarapids 16- by 5-foot, three-deck screen. It features a triple shaft adjustable mechanism that creates an elliptical screen motion, allowing the screen to be adjusted to the material being separated. The H5163 is recommended for natural and crushed aggregate, and recycled concrete and asphalt, among other applications.
Improved pump flow
The QP2H is the newest Multiquip 2-inch pump. It replaces the QP2H, offering improved performance with more flow and head. It can pump up to 158 gallons per minute with a maximum head of 115 feet.
Extends belt life inexpensively
Flexco says its new Flex-Lag Diamond Ceramic Lagging is an economical approach to extending belt life and increasing productivity while providing a reliable solution to belt slippage. Designed for use with medium-tension conveyor pulleys, it is also recommended for existing rubber lagging applications that experience high levels of wear and tear. The new product has a large ceramic tile molded into the diamond section of the lagging, providing an increased coefficient of friction. The tiles are surrounded by multiple channels for dispersement of water and renegade materials.
McCloskey says its new “right-size” stackers deliver higher piles of material at a lower cost. The new 65St and 80St stackers have been redesigned to match the weight of each unit to its height and load requirements. As a result, the company has reduced the cost of the units, which were initially designed to withstand the most severe demands on larger equipment. Both units feature McCloskey’s patented counterweight design, which is said to yield higher material piles, adding 50 percent or more material to each stockpile.
Liners improve uptime
W.S. Tyler says its new polyurethane bar rail liners protect tension poly screens and extend the service life of traditional wire mesh screens. Tyrethane Bar Rail Liners are said to have 20 to 30 times the service life of inexpensive rubber liners and can be used to support all metal media options.
Large, versatile crushers
Exhibiting at ConExpo-Con/Agg for the first time ever, Kleemann introduced two large, versatile mobile processing plants to the North American market. The impactor-based MOBIREX MR 130-Z is a closed-circuit machine with a fully independent two-deck prescreen before the primary impact crusher box. Material is dropped onto a feeder, scalped over the independent pre-screen, and through an onboard screen after the crusher, where oversize is recirculated back into the crusher. Kleemann says it is two machines in one: a crusher, and a screen box. Also debuting was the MOBICAST MC 120-Z, featuring a 48- by 32-inch jaw crusher. It has an independent double-deck pre-screen with a feeder under the crusher. The complete machine weighs 72.5 tons.
Faster, easier fastening system
Flexco introduced its new BR6 faster and fastening system at this year’s ConExpo-Con/Agg show, saying it offers a faster and easier solution to belt tensions and pulley diameters that cannot be handled by the company’s BR10 system. The system is said to be ideal for troughed belts with 20- and 35-degree troughing idlers. The BR6 fasteners can handle tensions from 330 to 400 PIW and conveyor systems with pulleys as small as 14 inches and operating tensions at 75 percent to 100 percent of tension ratings. The system requires only six rivets per fastener and can be purchased in full-width strips of 24, 30, 36, and 42 inches. Flexco says it can also be used as an alternative to vulcanized applications and straight warped belting.
New Class 8 truck
International’s new Paystar 5900i is a Class 8 vocational on-highway/off-highway truck that features a new wide-track, set-back axle design for front axle load distribution and improved maneuverability. The new model has engine choices ranging up to 625-horsepower, and International says its standard frame rail has the highest standard strength-to-weight ratio in the field — 2.3 million RBM — and an optional double frame rail provides an increase to 4.7 million RBM.
Terex Reedrill’s new 300-horsepower R30C drill has a longer, 5-foot boom extension for increased reach and can drill three or even four holes per setup, according to the company. It also has an optional capability for 51-mm steel. Other improvements include fewer moving parts, and the company’s SmartDrill drilling system, which uses anti-jam, anti-plug, and anti-plunge features to lengthen drill-string life and improve overall production, according to the company.
MORE FROM Articles
SUBSCRIBE & FOLLOW
- Kelly Bailey named 2015 AggMan of the Year439 Views
- MSHA and NSSGA release new infographic about material handling injuries327 Views
- Miner suspended upside down pulled to safety by his pant legs194 Views
- Democratic senators call for shorter highway bill in order to maximize funding166 Views
- Topcon debuts the Falcon 8, a rotary wing drone for mass data collection117 Views