W.S. Tyler’s Hydro-Clean™ Cleans Contaminated Materials Using Up To 75% Less Water
ST CATHARINES, Ontario – The new Hydro-Clean™ washing unit from W.S. Tyler effectively cleans deleterious material from aggregate, recycled and other minerals while reducing water consumption by up to 75 percent over traditional log washers. Unlike traditional washing systems which can require up to three screens along with a log washer or screw, the producer only needs an additional wash screen for the Hydro-Clean’s discharged material. The Hydro-Clean is available in four model sizes that produce 20 to 400 TPH, depending on the application: the 350, 700, 1,000 and 2,000.
Taking a maximum feed material size of up to six inches (150 mm) into its vertical drum, the Hydro-Clean employs high-pressure nozzles, rotating at 90 rpm, to spray up to 90 percent recycled water on the material with pressures up to 2,900 psi (200 bars). The washing unit removes silt and clay particles as small as 63 microns from mineral mixtures and, with its short retention times, can process up to 400 TPH (tons per hour), depending on model size and application. Due to its compact size and weight, overall operating and structural costs are considerably lower than with traditional washing systems—which also require more equipment and a greater footprint.
The Hydro-Clean consumes little water and power. Water consumption ranges from 27 to 211 gpm, depending on application and model size—compared to log washers that can require up to 800 gpm of water. Power requirements for the Hydro-Clean are no greater than 300 hp (225 kW) on its largest model. When compared to conventional systems, the Hydro-Clean experiences little wear with a maintenance-friendly design that allows for easy exchange of the few standard components that are subject to wear.
Ideal for use in clay-heavy material deposits, dirty material is fed via hopper to a vertical washing drum, where high-pressure nozzles mounted at the top rotate and spray the material with water. The water streams spread and wash the material at pressures of up to 2,900 psi, effectively interacting with the material to break up agglomerates and clean the particles of stubborn material. The turbulence in the drum creates additional scrubbing and abrasive forces that enhance the cleaning process as the material travels down the drum cylinder. High-pressure streams of water are injected into areas of the rock (holes, cracks, etc.) that are difficult to reach with traditional cleaning methods like log washers or screws – creating a cleaner product that generates higher selling value. In addition, many producers use this unit to turn material that was once dirty waste into revenue.
During the cleaning process, the washed material works its way down the drum and exits onto a discharge conveyor that leads to a standard wash screen, removing any remaining dirt or clay still on the stone as it fractionates the material. The resulting dirty water flows through polyurethane screen mesh installed in the sides of the washing drum. It is collected by a waste water pipe, which sends the water to a treatment system for additional fine screening.
The distance between the washing rotor and the material bed in the Hydro-Clean is variable and allows the system to adapt to various material types. Level sensors located at the material feed inlet provide exact data to the PLC control unit, ensuring a consistent material flow into the system.
W.S. Tyler, a St. Catharines, Ontario-based member of the Germany-based Haver Screening Group, is the only company in the world that provides premium screening solutions encompassing the complete screening circle of particle analysis, screening media, vibrating screens and process equipment, and complete production analysis, service and parts support. A global leader in mineral processing technology, the group is renowned for its exceptional quality and commitment to continually redefine screening by bringing innovative solutions to the market. For more information, call 1-800-325-5993 or visit www.wstyler.ca.
From our partners
The new Sandvik Ranger surface drill rig offers renowned drilling efficiency with up to 20% lower fuel consumption
Known to many by their former name, Ranger, Sandvik’s DX series surface…
MORE FROM Aggregates Zone
SUBSCRIBE & FOLLOW
- MSHA issues citations to five metal/non-metal mines during impact inspections in February446 Views
- Holcim shareholders threaten merger plans with Lafarge…again321 Views
- California woman killed when gravel truck tips over on her car210 Views
- Trinity Materials' Indian Village Plant is diggin’ Cajun style176 Views
- Caterpillar intros 735C, 740C EJ, 745C articulated trucks with bevy of powertrain improvements (PHOTOS)172 Views